Home
Latest images
Register
Log in
Admin -=C.J.S=-
nathan2012
[center]UNIT: nokia 101
STATUS: no power
ACTION TAKEN: Jumper
TOOLS: Iron,tweezer,jumper wire,led
PROCEDURE:
1.Flash ko cya sa hti
2.do reset all[no luck}
LOGS:
[code]Backup saved to "C:\mobileEx\3.5\data\backup\XGOLD_RM-769_F6039B465C1A44EA_IMEI.back"
MXKEY [MxKey Team HTI PLUS Flasher Interface 4], SN: C0821465
Using device: HTI, FW ver: 00.50, SN: 01007958
Connection status: OHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.20814(05-05-2012), Library ver: 1.0.0.14060(05-05-2012)
Device synchronized.
CPU: XGOLD 110
Using embedded SBL from MCU.
Sending EBL Loader ...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.24
EBL version: Default_RAM_Bootloader
Set baud rate to: 921.60 Kbit/s
Flash ID: 00EC 2404 - 23280002 [Samsung K5N2833ATM,128 Mbits]
CFI information:
Flash settings: 0/1, size: 0x01000000
2 Block regions:
255 x 0x00010000 = 0x00FF0000
8 x 0x00002000 = 0x00010000
EBL ready !
Processing file: rm769_006.900
Downloading item CODE:hw_f3_rm769_r06.900.fls, num block: 3, size: 5.58 MB
Erasing area 0x00000000-0x00005FFE ...OK
Programming completed in 0.609 s
Erasing area 0x00800000-0x00BEFFFE ...OK
Programming completed in 1 min 40.610 s
Erasing area 0x00C5D000-0x00DFB6FE ...OK
Programming completed in 34.281 s
Checksum verified (0x3F24)
Processing file: rm769_006.90ic
Downloading item CUST:hw_f3_rm769_006.90ic.fls, num block: 1, size: 4.80 MB
Erasing area 0x00100000-0x005CACFE ...OK
Programming completed in 1 min 42.875 s
Checksum verified (0x317E)
Processing file: rm7690_nai06.90ic
Downloading item CUST:hw_f3_rm7690_nai06.90ic.fls, num block: 1, size: 715.83 KB
Erasing area 0x00E60000-0x00F1223E ...OK
Programming completed in 14.532 s
Checksum verified (0x1E8E)
Total time for flashing process(boot+erase+write) was 6 min 11.297 s
Phone type: RM-769
SW version: V 06.90 07-03-12 RM-769 (c) Nokia
Imei plain: 35907204890856-6
Product code: 059H0F4
Cellular system: GSM
ASIC ID: 0x2292, type: 11
Ppm Id: IC
Language Pack:
- not available.
Imei net: 35907204890856
Provider: GSM Test Operator
Counter: 0/3, 0/10
CONFIG_DATA: 0010100000000000
PROFILE_BITS: 0000000000040002
BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
FULL FACTORY... OK
USER DATA... OK
LEAVE FACTORY... OK
SERVICE CENTER... OK
SOFTWARE UPGRADE... OK
PRODUCTION TUNING... OK
Reset User Code (to default:12345) ... OK
Completed in 1.656 s
3.Baklas ang unit
4.trace ko lines ng lcd
5.At nakita ko my putol isang linya
6.kaya jumper ko na...
Ito na po yung finish products:
For reference lang po,sana makatulong...
STATUS: no power
ACTION TAKEN: Jumper
TOOLS: Iron,tweezer,jumper wire,led
PROCEDURE:
1.Flash ko cya sa hti
2.do reset all[no luck}
LOGS:
[code]Backup saved to "C:\mobileEx\3.5\data\backup\XGOLD_RM-769_F6039B465C1A44EA_IMEI.back"
MXKEY [MxKey Team HTI PLUS Flasher Interface 4], SN: C0821465
Using device: HTI, FW ver: 00.50, SN: 01007958
Connection status: OHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.20814(05-05-2012), Library ver: 1.0.0.14060(05-05-2012)
Device synchronized.
CPU: XGOLD 110
Using embedded SBL from MCU.
Sending EBL Loader ...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.24
EBL version: Default_RAM_Bootloader
Set baud rate to: 921.60 Kbit/s
Flash ID: 00EC 2404 - 23280002 [Samsung K5N2833ATM,128 Mbits]
CFI information:
Flash settings: 0/1, size: 0x01000000
2 Block regions:
255 x 0x00010000 = 0x00FF0000
8 x 0x00002000 = 0x00010000
EBL ready !
Processing file: rm769_006.900
Downloading item CODE:hw_f3_rm769_r06.900.fls, num block: 3, size: 5.58 MB
Erasing area 0x00000000-0x00005FFE ...OK
Programming completed in 0.609 s
Erasing area 0x00800000-0x00BEFFFE ...OK
Programming completed in 1 min 40.610 s
Erasing area 0x00C5D000-0x00DFB6FE ...OK
Programming completed in 34.281 s
Checksum verified (0x3F24)
Processing file: rm769_006.90ic
Downloading item CUST:hw_f3_rm769_006.90ic.fls, num block: 1, size: 4.80 MB
Erasing area 0x00100000-0x005CACFE ...OK
Programming completed in 1 min 42.875 s
Checksum verified (0x317E)
Processing file: rm7690_nai06.90ic
Downloading item CUST:hw_f3_rm7690_nai06.90ic.fls, num block: 1, size: 715.83 KB
Erasing area 0x00E60000-0x00F1223E ...OK
Programming completed in 14.532 s
Checksum verified (0x1E8E)
Total time for flashing process(boot+erase+write) was 6 min 11.297 s
Phone type: RM-769
SW version: V 06.90 07-03-12 RM-769 (c) Nokia
Imei plain: 35907204890856-6
Product code: 059H0F4
Cellular system: GSM
ASIC ID: 0x2292, type: 11
Ppm Id: IC
Language Pack:
- not available.
Imei net: 35907204890856
Provider: GSM Test Operator
Counter: 0/3, 0/10
CONFIG_DATA: 0010100000000000
PROFILE_BITS: 0000000000040002
BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
FULL FACTORY... OK
USER DATA... OK
LEAVE FACTORY... OK
SERVICE CENTER... OK
SOFTWARE UPGRADE... OK
PRODUCTION TUNING... OK
Reset User Code (to default:12345) ... OK
Completed in 1.656 s
3.Baklas ang unit
4.trace ko lines ng lcd
5.At nakita ko my putol isang linya
6.kaya jumper ko na...
Ito na po yung finish products:
For reference lang po,sana makatulong...
